The Wireless M-Bus (wM-Bus) to the NB-IoT Converter enables the collection and transmission of the data from existing meters using the open wM-Bus standard as well as the selected proprietary protocols.
The converter is particularly useful for property management companies and water utilities that need to connect their existing meters to comply with the European EED directive without the need to replace the meters themselves.
NB-IoT connectivity – today, the Narrowband IoT coverage is available almost everywhere, with a reach even in hard-to-access areas. Additionally, SIM cards can be obtained for as little as 1 EUR per year.
The antenna connector for the wM-Bus reception is designed to minimize losses, ensuring the highest possible reception sensitivity. As a result, we can cover up to 6 floors, depending on the type of building.
The internal NB-IoT antenna provides sufficient coverage and eliminates the need for two external antennas, preventing the possibility of them being swapped during the installation.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
.webp)
Waterproof casing (IP67) for the outdoor installations – for example, even on the street lighting in the middle of a housing estate.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
During the manufacturing, we insert your SIM card, connect the battery and upload your configuration. This way, you don't need to spend extra time on the device and it can go directly to the installation.
NB-IoT connectivity – now offers coverage almost everywhere, reaching even into basements and SIM cards can be obtained for as little as 1 EUR per year
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
WAGO connector – the industry-standard terminal block for a quick and secure connections. It shortens the installation time and helps to eliminate mistakes caused by the insufficient wire tightening in the terminal block.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring a long battery life even with the frequent data readings.
IP67 waterproof enclosure for the outdoor installations – suitable even for the mounting on the wall of a heat exchange station.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
Support for up to 16 connected devices, providing maximum installation flexibility and ensuring that you won't need to return for a second device if there's one more meter than expected.
Data filtering at the hardware level using the VIF and the DIF values for the efficient shortening of the M-Bus message. The message remains standardized and can be processed by any M-Bus parser.
The converter, with a support for the M-Bus standard, is compatible with various meters from different manufacturers, ensuring the versatility and the easy integration.
For the demanding applications, a version with an external power is available, providing the continuous power supply to the M-Bus.
Data filtering at the hardware level using the VIF and the DIF values for efficient shortening of the M-Bus message. The message remains standardized and can be processed by any M-Bus parser.
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
WAGO connector – the industry-standard terminal block for a quick and secure connections. It shortens the installation time and helps to eliminate mistakes caused by the insufficient wire tightening in the terminal block.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
Communication tested within the largest LoRaWAN networks in Europe as well as in the isolated systems.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring a long battery life even with the frequent data readings.
%20na%20LoRaWAN2.webp)
IP67 waterproof enclosure for the outdoor installations – suitable even for the mounting on the wall of a heat exchange station.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
Support for up to 16 connected devices, providing maximum installation flexibility and ensuring that you won't need to return for a second device if there's one more meter than expected.
Data filtering at the hardware level using the VIF and the DIF values for the efficient shortening of the M-Bus message. The message remains standardized and can be processed by any M-Bus parser.
The converter, with a support for the M-Bus standard, is compatible with various meters from different manufacturers, ensuring the versatility and the easy integration.
For the demanding applications, a version with an external power supply is available, that enables the continuous M-Bus power supply.
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
WAGO connector – the industry-standard terminal block for a quick and secure connections. It shortens the installation time and helps to eliminate mistakes caused by the insufficient wire tightening in the terminal block.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
Communication tested within the largest LoRaWAN networks in Europe as well as in the isolated systems.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring a long battery life even with the frequent data readings.
IP67 waterproof enclosure for the outdoor installations – suitable even for the mounting on the wall of a heat exchange station.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
The converter is compatible with various protocols, including Modbus RTU, Modbus ASCII, IEC 62052 and DLMS.
Support for up to 128 connected devices, providing the maximum flexibility during the installation and ensuring that you won’t need to return for a second device if there's one more meter than expected.
For the demanding applications, a version with an external power supply is available, allowing the continuous power supply to the sensors.
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
WAGO connector – the industry-standard terminal block for a quick and secure connections. It shortens the installation time and helps to eliminate mistakes caused by the insufficient wire tightening in the terminal block.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
NB-IoT connectivity – now offers coverage almost everywhere, including the underground levels and SIM cards can be obtained for as little as 1 EUR per year.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring a long battery life even with the frequent data readings.
IP67 waterproof enclosure for the outdoor installations – suitable even for the mounting on the wall of a heat exchange station.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
The converter is compatible with various protocols, including Modbus RTU, Modbus ASCII, IEC 62052 and DLMS.
Support for up to 128 connected devices, providing the maximum flexibility during the installation and ensuring that you won’t need to return for a second device if there's one more meter than expected.
For the demanding applications, a version with an external power is available, allowing the continuous power supply to the external sensors.
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
Support for up to 4 connected devices, providing the maximum flexibility during the installation. This ensures that you won’t need to return for an additional device if there’s one more meter than expected during the installation.
Thanks to the standard SMA connector, you can use a cable to extend the antenna from the hard-to-reach places.
Communication tested within the largest LoRaWAN networks in Europe as well as in the isolated systems.
Two-piece EUROCLAMP connector – an industry-standard two-piece terminal block for quick and secure connections. The advantage of the two-piece terminal block is the ability to prepare the meter connections in advance and then simply attach the terminal block to the PCB.
A big battery with a lifespan of over 10 years, considering the frequency of readings.
IP67 waterproof enclosure for the outdoor installations – suitable even for the mounting on the wall of a heat exchange station.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
The converter, with its wide input tolerance, is compatible with various meters from different manufacturers, ensuring the versatility and an easy integration.
Storing the historical readings and repeatedly sending them in each message to ensure the data recovery even if one or two messages are lost.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring long battery life even with the frequent data readings. For the demanding applications, a version with an external power is available.
Support for up to 4 connected devices, providing the maximum flexibility during the installation. This ensures that you won’t need to return for an additional device if there’s one more meter than expected during the installation.
NB-IoT connectivity – these days, it already has a coverage almost everywhere, with the ability to reach even the basements. SIM cards can be obtained for as little as 1 EUR per year.
Two-piece EUROCLAMP connector – an industry-standard two-piece terminal block for quick and secure connections. The advantage of the two-piece terminal block is the ability to prepare the meter connections in advance and then simply attach the terminal block to the PCB.
The antenna connector is designed to minimize losses, ensuring the highest possible reception sensitivity. This allows you to use the device inside a heat exchange station while still maintaining a strong signal.
The device can be used inside a heat exchange station and despite the high-temperature environment, it provides a stable signal. Thanks to the standard SMA connector, you can use a cable to extend the converter from the hard-to-reach places.
A large battery with a lifespan of over 10 years, taking into account the frequency of readings.
Waterproof enclosure (IP67) for the outdoor installations – ideal for mounting on the wall of a water meter shaft.
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
The converter, with its wide input tolerance, is compatible with various meters from different manufacturers, ensuring the versatility and an easy integration.
Storing the historical readings and repeatedly sending them in each message to ensure the data recovery even if one or two messages are lost.
For the installations without an electrical power supply, the converter is available in a battery-powered version, ensuring long battery life even with the frequent data readings. For the demanding applications, a version with an external power is available.
A display on the device for the immediate viewing of the reading, time and the unique gas meter ID, configurable by the user.
An internal antenna for the ATEX certification compatibility and to accelerate the installation process.
A user-replaceable battery with a lifespan of over 10 years, considering the frequency of readings.
WAGO connector – the industry-standard terminal block for the quick and secure connections. It shortens the installation time and helps to eliminate mistakes caused by the insufficient wire tightening in the terminal block.
NB-IoT connectivity – now has the coverage almost everywhere, reaching even to the basement levels and SIM cards can be obtained for as little as 1 EUR per year.
Interface for an optical head and configuration through the IEC 62056-21 interface – an industry standard used in the gas meters. This standard allows you to integrate the device directly into your configuration software.
.webp)
Screws that won't fall out of the cover during installation make the assembly easier and ensure that the IP rating of the converter is not compromised.
Waterproof enclosure (IP67) for the outdoor installations.
Interface for the optical head and configuration via IEC 62056-21 interface - industry standard used in gas meters. This standard allows you to integrate the device directly into your configuration software.
Storage of the historical readings for up to 40 days with the option for the local or remote retrieval.
All of these challenges have been solved. ACRIOS Systems converters are designed to cover the widest range of meters, from open standards like wM-Bus OMS to various proprietary protocols—whether it’s Sontex Supercom, Apator Metra protocol or Sensus Bubble UP, we can handle it.
The converter is designed for a seamless integration into existing systems. We use dual D-Cell batteries, which easily provide a lifespan of over 10 years.
.webp)
Maddalena
B-Meters
Apator Metra
Sontex
Diehl
Sensus
Ostatní
Qundis
and others
.webp)
.svg)
"The remote gas meter reading devices from ACRIOS have proven their reliability and quality of workmanship. We appreciate that all our technical requirements were met and that we received all the necessary documentation and technical support for integration into our information system. We are very satisfied with the cooperation..“
ACRIOS was instrumental in our success on a large-scale European deployment of the wM-Bus concentrators, helped to solve all of the technical challenges and deliver results within the set deadlines.
ACRIOS’ reliable products for remote readings and innovative, fully customizable solutions perfectly complement our expertise in value-added distribution of IoT products and solutions. We are proud to collaborate with a company that shares our commitment to excellence and customer satisfaction.
.webp)
We successfully integrated the ACRIOS Data Concentrator into our smart metering project, seamlessly connecting hundreds of meters. The device’s performance and stability have been outstanding, even in challenging environments. The LoRaWAN protocol used by the concentrator ensures strong, reliable signal coverage, even in hard-to-reach areas. We highly recommend the ACRIOS Data Concentrator to anyone looking to enhance their smart metering infrastructure.
“The ACRIOS scripting capabilities have provided Netmore with the required solution for solving integrations with MBUS/MODBUS units.”
We offer the ACRIOS remote reading solutions to all of our customers who want to comply with the EED decree. The solution is quick to install, requires no training and proves to be stable over time.
“We were searching for a way that would allow us to connect existing M-Bus and MODBUS meters to our LoRaWAN network and found the solution provided by ACRIOS valuable for these use cases.“
.webp)
.webp)